By Raul A. Angulo

My favorite tool is the pickhead ax not only because it can cause major damage but because, along with the fire helmet, it's the most recognized iconic symbol of our profession. However, after 35 years on the job, whether I'm on an engine or a ladder company, if I had to choose between grabbing the ax or a D-handle pike pole, I'd choose the pike pole. I'm not saying this is the only tool we need, but I am saying if you're on an engine or a truck, someone on your crew should have a pike pole as part of the tool complement they're carrying in and here's the reason: In addition to the hoseline and the thermal imaging camera, the crew usually carries the irons (a halligan tool and a flathead ax), an A tool, or a pickhead ax. All these tools are fine and may even be necessary, but after forcible entry is made, they lack the reach that's provided by the pike pole. Once your crew is inside the structure, there are numerous scenarios that require extra reach that are difficult to accomplish with regular forcible entry tools.

(1) During a vertical ventilation operation, it is essential that the team has a pike pole of sufficient reach to punch through the ceiling below. Even during this drill on an acquired structure, the pike pole is too short to punch through the ceiling. Notice how the firefighter's face and torso are directly over the vent hole. His entire arm is reaching through the attic space to reach the ceiling. This is a very dangerous position. When hot fire gases and smoke flash during vertical ventilation, it happens with lightning speed. There would be no time for this firefighter to react. He would be engulfed in smoke, heat, and flame. Having a 12-foot pike pole would allow the firefighter to stand windward, away from the vent hole, and still accomplish the objective. (Photos by author.)

The pike pole is a simple design-it's just a pointed hook at the end of a stick-but it's uniquely versatile for the many tasks crews may have to perform on the fireground. Let's look at the general sequence of some realistic fire attack scenarios where the pike pole is invaluable. All references will imply using a D-handle pike pole.

Forcible Entry

First is access and forcible entry. Say you come across any variety of wooden fences. A pike pole can easily pull slats from the stringers or maybe even pull down an entire section of fence. I've done it. The D-handle can also be used to punch the slats away from the horizontal cross members, creating a passageway through the fence.

(2) Leader-North America's telescopic pike pole weighs six and a half pounds. Retracted, it measures seven feet, two inches. Fully extended, it measures 12 feet, three inches. It has a carbon steel head and insulates up to 20,000 volts of electricity, a comforting safety feature. The black center easy-twist mechanism locks the pike pole at the desired length.

A pike pole can be used to help pry and lift up a garage door or a roll-up door. It can also be used to wedge such a door in the up position, preventing it from accidentally closing on the entry team or compressing the charged hoseline. This situation has trapped and killed more than one firefighter. Once the door is opened and the hook is in place, consider placing a vise grip onto the track rail or even replace your hook with a small A-frame ladder to hold the door open so you still have your tool for firefighting activities. Consider the height adva

Bill Adams

This is the first in a series profiling individual fire apparatus dealers-the people who sell fire trucks. Although some apparatus are sold factory direct, the majority of sales are through an agent or a broker-an intermediary between purchaser and manufacturer. An agent can also be called a dealer, a dealership, or a sales representative. For the sake of simplicity, this article defines a dealer as an entity that customarily enters into a contractual agreement with a manufacturer to sell product in a given geographical territory. I define a dealership as a dealer who has a physical workplace-a place of business similar to a showroom or service facility. A sales representative, the person fire departments deal with on a face-to-face basis, can be a factory employee, a dealer's employee, or the dealer principal himself.

The intent is not to judge a dealer because of size, longevity, or capability. The objective here is to give the purchaser an understanding of who some fire apparatus dealers are, their business philosophies, and how they got where they are today.

(1) These four aerial devices are being "flown" behind Greenwood's Sales & Administration building for its 2012 open house. (Photos by author.)

Beginning

In the late 1970s, three friends in Southern Massachusetts-Mark France, a retired captain with the Attleboro (MA) Fire Department; Robert Allard, a mechanic with the same department; and Tim O'Neill-contemplated going into the automotive business together. Allard suggested a shop large enough to accommodate his expertise-repairing fire apparatus. They did and formed Greenwood Motors in 1979. Emergency One (E-ONE), based in Ocala, Florida, which had just started in 1974, was expanding its dealer network, and Greenwood signed on as E-ONE's New England dealer in May 1979. It has experienced steady, planned growth ever since. E-ONE's Web site shows Greenwood being its second oldest dealer-surpassed by one who signed on just three months earlier. Dealer longevity with a single fire apparatus manufacturer is an anomaly in today's marketplace.

I had the opportunity to interview Greenwood's principals at their sales and administration office and later observe their employees interacting with customers and vendors during their September 2012 open house. Commenting on Greenwood, Alan Hollister, E-ONE's northeast region sales director, says, "Greenwood is considered by E-ONE to be one of our premier dealers. A truly professional organization, their strength lies in a firm commitment to customer satisfaction and unmatched customer service." O'Neill is president and owner. Executive vice president is Dennis Carvalho, and Mark MacDonald is vice president of sales.

(2) The product mix at the 2012 open house included a mini pumper, a stainless steel bodied pumper, straight aerials, quints, a tower ladder, a heavy rescue, numerous extruded aluminum pumpers on both custom and commercial chassis, many styles of ambulances, and an aerial that was refurbished in Greenwood's shops.

Growth

In 1979, the business opened a sales and service facility in North Attleboro, Massachusetts, and the business incorporated as Greenwood Motors. A larger building followed in 1984, and the name changed to Greenwood Fire Apparatus. The company built a separate sales and administration

By Robert Tutterow

Last Christmas Eve's Webster, New York, firefighter ambush that killed two volunteer firefighters and wounded two others once again brought the subject of violence against firefighters to the forefront. This incident was one of a growing number of acts of violence against firefighters. National Fire Protection Association (NFPA) statistics reveal that, on average, there are three firefighter line-of-duty deaths (LODDs) annually from assaults. It is estimated that there are well over a million assaults against firefighters and EMS personnel annually in the United States. Anecdotal evidence also indicates that more than 90 percent of firefighters have been verbally or physically assaulted.

If you are a firefighter reading this column, you can probably recount one (maybe several) assaults. Violence against firefighters is not a new thing.

Thirty years ago, I responded with my volunteer fire department to a reported vehicle fire at an auction barn in rural North Carolina. It was an early Saturday evening, and an auction had just started. On our arrival, the fire had been extinguished. However, people were running out of the auction barn screaming, "He has a gun!" The owner/auctioneer came out of the barn and threatened all of us volunteer firefighters. We stood still, remained silent, let him vent, and then it was all over.

This situation was perhaps unique in that we all knew the owner/auctioneer. He was known as "Dud," and he liked alcohol and women. Apparently, he had a little too much of at least one of his two life pleasures that evening. I don't think any of us felt his threats were sincere, for he had a generous side. Dud was a well-known character who always carried a lot of money-and a gun. He never hesitated to peel off a few bills from the roll of cash he carried during fire department fundraisers. Nonetheless, this incident gave me pause to think how a similar situation in a different setting could have a bad outcome.

The fire service collectively acknowledged violent acts against firefighters in 2004 when the National Fallen Firefighters Foundation (NFFF) issued its 16 Life Safety Initiatives. Initiative #12 states, "National protocols for response to violent incidents should be developed and championed." The issue is also addressed in NFPA 1500, Standard on Fire Department Occupational Safety and Health Program. Chapter 8, "Emergency Operations," has a section titled "Scenes of Violence, Civil Unrest, or Terrorism."

Acts of Violence

Acts of violence can occur in many ways. The Webster ambush was staged by the assailant setting his house on fire. In 2004, the Lexington (KY) Fire Department lost a firefighter when she was shot during a domestic dispute. Firefighter/EMT Brenda Denise Cowan was in the yard providing aid to the wife of the assailant, whom he shot. She was also the first black female to die in the line of duty in the United States.

In 2008, a Maplewood, Missouri, firefighter was shot and killed at the scene of a vehicle fire by an awaiting sniper. Twenty-two-year-old Ryan Hummert, son of the former mayor, was on his first fire call. The sniper also shot and wounded two police officers.

In the Aurora, Colorado, theater mass shooting in July 2012, the shooter had booby-trapped his apartment to kill emergency responders through an array of ignition systems, chemicals, and a trip wire.

Some of you may recall that many of the tillered aerials in Los Angeles had to be removed from service during the riots following the Rodney King trial in 1992. It was apparent that the tiller person was a sitting duck for rioters.

And, violence against firefighters can occur at places other than an emergency scene. Seventeen years ago, a Jackson, Mississippi, firefighter shot and killed his wife and then went to the central fire station, where he opened f

Alan M. Petrillo

Pump manufacturers have responded to fire department requests for fire apparatus pumps that can flow plenty of water yet take up the least amount of space on their vehicles so any extra space saved can be dedicated to equipment storage or other uses.

Narrowing Pumps

Jon Moore, national sales manager for Hale Products Inc., says that his company's QMAX-XS-the XS stands for extra space-is a slimmed down version of its popular QMAX pump with the same flow characteristics and in the same versions that will generate from 1,250 to 2,000 gallons per minute (gpm).

Moore notes that the QMAX-XS takes a foot off the pump box with no loss of functionality. "The QMAX is our most reliable and largest selling pump," Moore says. "It's virtually indestructible and delivers very good performance. The XS version builds on those characteristics but in a smaller package that saves space on a vehicle and has many interchangeable parts with the QMAX."

Hale isn't a stranger to putting the most amount of performance into a smaller package, Moore notes. "We came out with the QPAK, a pump rated from 750 to 1,000 gpm, about 20 years ago and it was the original small pump for the fire service," he says. "This was the smallest version available of a fully manifolded midship pump."

(1) The Waterous CXS end suction pump with ram's horns on the pump's inlet allows the company to put a 1,500-gpm pump into a 28-inch-wide package when using electric discharge valves. (Photo courtesy of Waterous.)

He adds that the QPAK can be run off of a J gearbox for a left or right power takeoff (PTO) or off of a standard G gearbox for a split-shaft midship drive off the vehicle's transmission. "QPAK is a very slim pump that sets up well for smaller chassis and for tankers where you want a smaller pump box," Moore says. "It also works well in smaller brush trucks. It's the original pump that started the series of narrow pumps we have out now, like the QMAX-2 and the QFLO."

Bruce Senn, Hale's Southeast regional sales manager, says Hale also makes the Sidekick, a pump available in the 500- to 1,500-gpm range but that doesn't require a conventional pump box. "Sidekick fits in a compartment and can be narrowed down to 24 inches wide," Senn says. "It's great for rescues and tankers. The pump is available as both a package and a kit that bolts to the side of the frame rail and works with several different models of pumps."

(2) The S101 end suction pump made by Waterous uses schedule 10 stainless steel plumbing and can fit into a 38-inch pump house for a 1,500-gpm model. (Photo courtesy of Waterous.)

End Suction

Paul Darley, president and chief executive officer of Darley, says the fire industry has seen a strong move away from big midship fire pumps and toward end suction pumps. "End suction allows an apparatus builder or pump manufacturer to custom design the pump manifolds-the suction and discharge manifolds-which can free up a lot of space in the pump compartment that can be put to other uses."

Darley says one of the key driving forces in putting bigger pumps in smaller packages is the freeing up of space on fire apparatus for other uses. "The second key is the availability of large or full torque PTOs, and the third key is pricing,"