Menu

WFC News

Posted: Jan 1, 2019

Custom Rear-Mount Rosenbauer Pumper

Alan M. Petrillo

The Mt. Lebanon (PA) Fire Department had a number of issues to be addressed in the specs for a new pumper, mainly a rear-mount pump, strict angles of approach and departure, dual hydraulic ladder racks, as low a hosebed as possible, and both Class A and Class B foam tanks. Mt. Lebanon found the answer to their needs from Rosenbauer.

“Our district is in the foothills of Pennsylvania where we are a first-ring suburb outside of Pittsburgh,” says Rodger Ricciuti, Mt. Lebanon’s deputy chief. “We needed a pumper that has a drivetrain geared toward the low-end torque because we wanted pickup rather than top speed because of all the hills we encounter,” Ricciuti says. “There are some very steep transitions on some of the roads in town.”

Ricciuti points out that light rail transit runs through town and includes a 2,800-foot-long tunnel. “We have a suburban character to our fire district with an urban density,” he says. “US 19 highway cuts us in half, and we have three high schools as well of lots of other large residential and commercial buildings to deal with.”

Rosenbauer built this rear-mount custom pumper for the Mount Lebanon (PA) Fire Department on a Commander chassis with a 60-inch-long, 100-inch-wide cab with 11-inch raised roof. (Photos 1-5 courtesy of Rosenbauer.)

1 Rosenbauer built this rear-mount custom pumper for the Mount Lebanon (PA) Fire Department on a Commander chassis with a 60-inch-long, 100-inch-wide cab with 11-inch raised roof. (Photos 1-5 courtesy of Rosenbauer.)

The pumper is powered by a Cummins 500-hp 12-liter ISX12 engine and an Allison 4000 EVS automatic transmission.

2 The pumper is powered by a Cummins 500-hp 12-liter ISX12 engine and an Allison 4000 EVS automatic transmission.

The pumper’s physical specs include a 193-inch wheelbase, 32-foot 10-inch overall length, and 10-foot 2-inch overall height.

3 The pumper’s physical specs include a 193-inch wheelbase, 32-foot 10-inch overall length, and 10-foot 2-inch overall height.

The pumper has all roll-up doors over compartments and carries a Harrison 10-kW hydraulic generator.
Read more
Posted: Jan 1, 2019

Where to Find Foam Concentrate


A large-scale flammable liquid fire or emergency can occur anywhere, since these commodities are used everywhere in the country. With this in mind, every department needs to be prepared should something go wrong while these flammable liquids are being transported through or stored in its jurisdiction.

The two biggest consumable resources fire departments would need for a flammable liquid event are water and foam concentrate. Being able to get large quantities of water into the unique places these events occur, like on interstates and railways, is something most jurisdictions have—or should have—a plan for, but foam concentrate is a much different aspect that is not readily available like water.

When you ask many fire officers and chiefs who they are going to call when they have a need for foam, you will get a wide variety of answers such as the airport, a fuel terminal or refinery, a higher level of government, or maybe the generic answer of “somebody.” Who is that somebody? Is it the local airport? Is it another fire department or a state agency? You might be surprised at the answer you could get if you call for these resources without having a predetermined agreement or actual understanding of how the process works.

No matter where the foam comes from, the foam’s owner is more than likely going to want some type of reimbursement promise, as foam concentrate is rather expensive. A 325-gallon tote of alcohol-resistive aqueous film forming foam (AR-AFFF) can cost more than $10,000. Most localities (and their taxpayers) or businesses (and their shareholders) aren’t always willing to share a consumable resource with such a high price tag that was probably purchased to protect some specific target hazard within their jurisdiction or facility. While in the heat of battle, firefighters generally aren’t concerned with what it costs. However, an agency that is going to send tens of thousands of dollars of foam to an incident wants to know who is going to pay for it. In most cases, the responsible party or party that caused the incident is liable for the cost of the response. The reimbursement process can vary from state to state, so it is important to understand how the reimbursement process works within your locality or state. It is also just as important for you to understand what your authority is within your jurisdiction to authorize the use of and high cost for foam and whether you are the organization using the foam or the organization sending the foam, especially in cases where the responsible party is not known or is not going to be able to pay.

AIRPORTS

Most commercial airports have larger quantities of foam both on their aircraft rescue and firefighting (ARFF) trucks and stocked as reserve. However, planning to use this foam is not always as feasible as many firefighters think because of Federal Aviation Administration (FAA) rules that govern the airports, including the on-site firefighting capabilities. FAA regulations require that a certain number (depending on airport size) of firefighters and ARFF trucks be on site and ready at all times to keep the airport open and in operation. Having any of these required resources leave the airport property would cause the airport to shut down and more than likely create chaos for travelers and airlines. Most airports aren’t going to shut down and create the chaos for travelers to help with an incident off the airport property. Some airports may, however, have staffing and equipment above and beyond what the FAA requires so they could be able to assist. To determine what your local airport has to offer, contact it and have that discussion to figure how when and how it can help.

Read more
Posted: Jan 1, 2019

Where to Find Foam Concentrate


A large-scale flammable liquid fire or emergency can occur anywhere, since these commodities are used everywhere in the country. With this in mind, every department needs to be prepared should something go wrong while these flammable liquids are being transported through or stored in its jurisdiction.

The two biggest consumable resources fire departments would need for a flammable liquid event are water and foam concentrate. Being able to get large quantities of water into the unique places these events occur, like on interstates and railways, is something most jurisdictions have—or should have—a plan for, but foam concentrate is a much different aspect that is not readily available like water.

When you ask many fire officers and chiefs who they are going to call when they have a need for foam, you will get a wide variety of answers such as the airport, a fuel terminal or refinery, a higher level of government, or maybe the generic answer of “somebody.” Who is that somebody? Is it the local airport? Is it another fire department or a state agency? You might be surprised at the answer you could get if you call for these resources without having a predetermined agreement or actual understanding of how the process works.

No matter where the foam comes from, the foam’s owner is more than likely going to want some type of reimbursement promise, as foam concentrate is rather expensive. A 325-gallon tote of alcohol-resistive aqueous film forming foam (AR-AFFF) can cost more than $10,000. Most localities (and their taxpayers) or businesses (and their shareholders) aren’t always willing to share a consumable resource with such a high price tag that was probably purchased to protect some specific target hazard within their jurisdiction or facility. While in the heat of battle, firefighters generally aren’t concerned with what it costs. However, an agency that is going to send tens of thousands of dollars of foam to an incident wants to know who is going to pay for it. In most cases, the responsible party or party that caused the incident is liable for the cost of the response. The reimbursement process can vary from state to state, so it is important to understand how the reimbursement process works within your locality or state. It is also just as important for you to understand what your authority is within your jurisdiction to authorize the use of and high cost for foam and whether you are the organization using the foam or the organization sending the foam, especially in cases where the responsible party is not known or is not going to be able to pay.

AIRPORTS

Most commercial airports have larger quantities of foam both on their aircraft rescue and firefighting (ARFF) trucks and stocked as reserve. However, planning to use this foam is not always as feasible as many firefighters think because of Federal Aviation Administration (FAA) rules that govern the airports, including the on-site firefighting capabilities. FAA regulations require that a certain number (depending on airport size) of firefighters and ARFF trucks be on site and ready at all times to keep the airport open and in operation. Having any of these required resources leave the airport property would cause the airport to shut down and more than likely create chaos for travelers and airlines. Most airports aren’t going to shut down and create the chaos for travelers to help with an incident off the airport property. Some airports may, however, have staffing and equipment above and beyond what the FAA requires so they could be able to assist. To determine what your local airport has to offer, contact it and have that discussion to figure how when and how it can help.

Read more
Posted: Jan 1, 2019

TICs and Water Rescue

Manfred Kihn

I’ve been asked many times during my training exercises if a thermal imaging camera (TIC) can be used for water rescues. The answer is, sure, but there are limitations. You must know when and when not to use the TIC, but having it with you in your toolbox means you are prepared if the situation calls for a TIC.

Carl Nix

First, let’s understand that there is no TIC on the market that can see into water. Second, the person or object you are searching for must be floating on the surface, meaning your TIC will not help you when fishing or recovering a body. Third, and probably the most important, not all TICs will float. Having said that, it might be best to fill a bucket of water or a sink at the fire station to see if your TIC floats. The last thing you want to do is drop it overboard from your marine unit by accident because you forgot to use the lanyard to secure it to yourself. I can see the paperwork now, “Chief, no one was more surprised than me when I heard a splash and watched the TIC disappear into deep darkness as it left behind a trail of bubbles.”

Understanding the limitations of your TIC is critical when responding to a water rescue call. (Photo courtesy of Bullard.)

1 Understanding the limitations of your TIC is critical when responding to a water rescue call. (Photo courtesy of Bullard.)

Two Experiences

I’ve had two experiences in my career with water rescues. One was working with the Coast Guard during a training exercise on the Great Lakes. The Coast Guard took one of its rescue swimmers, put him into a mustang ice and water rescue suit, and took him out in the vast wide-open water. Our exercise was to find the swimmer in a certain amount of time. I used elevation to my benefit and got up as high as I could on the Coast Guard cutter and started scanning the vast open waters. As I said at the beginning of this column, there are limitations when using a TIC that may or may not hinder your search.

Some of those limitations pertain to weather and water conditions. If it’s extremely windy, the water most likely will be choppy with white caps. In this situation, I wish you the best of luck in your search because it’s going to take a while for you to locate the swimmer. If calmer conditions prevail, then you are in luck and will have better success. In this situation, you will want to use your TIC’s field of view (FOV) and overlap your scanning process. Look sideways and up and down as far as you can, which will help you become accustomed to the water. If it’s daytime and the sun is out, you’ll see the water glistening; if it’s dark, the water will be glittering from the moonlight.

Once you have established a baseline of the water, now look for something that doesn’t belong and hopefully you will find the victim or object you are looking for. This day, I was in luck that the weather and water conditions were in my favor, and I spotted an object about 1,200 feet fro

Read more
Posted: Jan 1, 2019

TICs and Water Rescue

Manfred Kihn

I’ve been asked many times during my training exercises if a thermal imaging camera (TIC) can be used for water rescues. The answer is, sure, but there are limitations. You must know when and when not to use the TIC, but having it with you in your toolbox means you are prepared if the situation calls for a TIC.

Carl Nix

First, let’s understand that there is no TIC on the market that can see into water. Second, the person or object you are searching for must be floating on the surface, meaning your TIC will not help you when fishing or recovering a body. Third, and probably the most important, not all TICs will float. Having said that, it might be best to fill a bucket of water or a sink at the fire station to see if your TIC floats. The last thing you want to do is drop it overboard from your marine unit by accident because you forgot to use the lanyard to secure it to yourself. I can see the paperwork now, “Chief, no one was more surprised than me when I heard a splash and watched the TIC disappear into deep darkness as it left behind a trail of bubbles.”

Understanding the limitations of your TIC is critical when responding to a water rescue call. (Photo courtesy of Bullard.)

1 Understanding the limitations of your TIC is critical when responding to a water rescue call. (Photo courtesy of Bullard.)

Two Experiences

I’ve had two experiences in my career with water rescues. One was working with the Coast Guard during a training exercise on the Great Lakes. The Coast Guard took one of its rescue swimmers, put him into a mustang ice and water rescue suit, and took him out in the vast wide-open water. Our exercise was to find the swimmer in a certain amount of time. I used elevation to my benefit and got up as high as I could on the Coast Guard cutter and started scanning the vast open waters. As I said at the beginning of this column, there are limitations when using a TIC that may or may not hinder your search.

Some of those limitations pertain to weather and water conditions. If it’s extremely windy, the water most likely will be choppy with white caps. In this situation, I wish you the best of luck in your search because it’s going to take a while for you to locate the swimmer. If calmer conditions prevail, then you are in luck and will have better success. In this situation, you will want to use your TIC’s field of view (FOV) and overlap your scanning process. Look sideways and up and down as far as you can, which will help you become accustomed to the water. If it’s daytime and the sun is out, you’ll see the water glistening; if it’s dark, the water will be glittering from the moonlight.

Once you have established a baseline of the water, now look for something that doesn’t belong and hopefully you will find the victim or object you are looking for. This day, I was in luck that the weather and water conditions were in my favor, and I spotted an object about 1,200 feet fro

Read more
RSS
First43834384438543864388439043914392Last

Theme picker

Search News Articles