Bill Adams

Although some may deny partaking in the process and probably will publically renounce the practice, most fire departments write apparatus purchasing specifications (specs) around a preferred manufacturer-usually with the help of the local vendor. It's a common occurrence. Get over it. I do not favor or condone it, and this article will not address it. This is directed at purchasers who, in good faith, attempt to write "open" specifications in an honest attempt to solicit competitive bids for a new fire truck. Use caution. You might be confusing potential bidders by unnecessarily using meaningless adjectives and flattering adverbs in your document.

An adjective describes or modifies the subject of a sentence. In the sentence "I want a glass of water," water is the subject. In "I want a glass of warm water," warm is the adjective. It gives additional information about the subject. It's grammatically correct. An adverb enhances the adjective, giving further information about it. In "I want a very warm glass of water," very is the adverb. It also is an acceptable method of writing.

However, when writing fire apparatus specifications, if that additional information cannot be defined, measured, and compared, it is useless. It has no value. If words do not give clarity and specificity to the subject, leave them out or confusion, misunderstanding, and undue embarrassment can result. Apparatus manufacturers often use descriptive adjectives and complimentary adverbs to give a favorable impression of their product. That's life. Live with it. Outside specification writers may do likewise, perhaps to make their document look professional. Occasionally, fire departments will inadvertently use an indefinable description. All three may be clouding the subject and hindering the competitive bidding process. There's no room for descriptive adjectives and adverbs in fire apparatus purchasing specifications.

Competitive Bidding

In competitive bidding, a purchaser describes in measurable terms what it desires. The description must be quantifiable to potential bidders. It is imperative that purchasers be able to fairly evaluate and accurately compare what is being proposed to what was specified. If that process cannot be followed, you are wasting your time and the bidders'. How can you determine compliance to a requirement you can't define? The importance of writing a comprehensible description of what you want cannot be overestimated. Vague and indecipherable words and descriptions in a purchasing specification are the first steps in compromising the intent of the competitive bidding process.

The Marketplace

The fire apparatus marketplace is unstable. New apparatus sales have been reported off by 30 to 50 percent. When business was thriving, vendors (manufacturers, dealers, and salespeople) often did not bid against competitors' proprietary specifications, nor did they submit proposals for vague and unclear specifications. In the case of bidding on a competitor's spec, the success rate is somewhere between slim and none. In the case of vague specifications, bidders may have to expend an inordinate amount of time trying to decipher or guess what the fire department really wants or means.

Today many vendors are aggressive; they are hungry. Some may be brash enough to question a purchaser's written word-once considered blasphemous in the fire service. Some may tender a proposal equally as vague and unclear as the published purchasing specifications. How do you handle that scenario?

Accountability

The first lesson in Fire Truck Selling 101 was to never challenge the customer. That may no longer be the case. First, many vendors are forced to do so for economic survival. Second, and in my opinion, it appears new breeds of "determined" salespeople are entering the marketplace. Thi

By Richard Marinucci

Often little things that occur during an incident determine the overall effectiveness and success of the operation. Departments should pursue continual improvement in and must look at every aspect of their operations to see where incremental improvements can be made. One area to consider is the differences presented with changing seasons. Although not necessarily a major consideration, there are some things that change as summer temperatures increase. This would be true regardless of whether you are in the desert areas of Arizona, where there is little transition from winter to spring, or in the northern part of the country where there are more defined seasons.

Climate changes affect personnel, apparatus, and equipment. They also can present different emergencies to which departments respond. Therefore, it is prudent to review operations as the seasons change just to make sure everyone is on the same page. Complacency must not creep into the organization or its members because this will impact the quality of service provided and could affect firefighter health and safety. This is not a major challenge to an organization but one that warrants specific review to pay attention to the little details that determine the level of service provided.

Apparatus and Equipment

Increasing temperatures may adversely affect apparatus and equipment if crews do not follow manufacturer-recommended practices. It is a good idea to review owner's manuals and perform routine maintenance as seasons change. Review operating apparatus and equipment relative to summer conditions, especially equipment only used during very warm months. It may also be appropriate to check on items that do not need to be carried on the vehicle. For example, ice melting chemicals and salt no longer need to be on vehicles during the summer in cold-weather states and can be stored until the next season change.

Although not all apparatus has air conditioning, it has become almost a necessity in many organizations. As an example, departments providing EMS transport probably require this feature for the benefit of those receiving treatment. It also can provide an area for firefighter rehabilitation when operating in high temperatures. You need to make sure it is working properly long before it is needed.

In many fire departments, the threat of relatively small grass and brush fires exists during warmer months. As such, equipment for these incidents is not part of the standard furnishings year round. If this is the case, the equipment needs to be checked to make sure it is in the proper working condition and placed on apparatus in locations for the best access. A review of all equipment is necessary, even if brief in nature. Simple steps make sure all the bases are covered and personnel are prepared to do the best possible job.

Personnel Performance

Summer conditions can affect personnel performance as well as health and well-being. Excessive heat and humidity will warrant shorter work periods and appropriate rehabilitation time. This is not earth-shattering news, but a reminder is appropriate on occasion. Also remind personnel about the signs and symptoms of various heat-related illnesses. Firefighters not only need to consider their own situations but also should look out for the rest of their crew.

One item not often considered is sunscreen. If members are working in the direct sun, especially midday with exposed skin, you should do whatever you can to offer protection. This can be by covering up, sunscreen, or short stints of exposure. Again, this is not a big issue in the overall scheme of things but can be helpful when protecting personnel. Finally, hydrate, hydrate, hydrate! This is important throughout the day, not just during an incident. All of this also applies to training that takes place outside. There are examples of firefighters suffering adverse

Alan M. Petrillo

Developments in wildland urban interface (WUI) apparatus have taken a page from businesses that use customer satisfaction surveys and feedback, incorporating changes and modifications into rigs that firefighters and fire departments see as necessary to make their jobs easier and safer on the front lines of wildland fires.

Structure and Wildland Duties

Chad Trinkner, marketing manager of pumpers, fire suppression and aerial products for Pierce Manufacturing Inc., says that Pierce has seen an emphasis on maneuverable wildland units that can double as urban interface vehicles to fight structure fires or protect exposures when necessary. "Pierce makes Type I, II, and III urban interface and wildland vehicles on custom or commercial chassis," Trinkner says, "often customizing a vehicle to a very specific body design as we do for the Federal Bureau of Land Management (BLM)."

Trinkner notes that the BLM vehicle, called a Model 62, is a spinoff of the United States Forest Service's (USFS) Model 34 Type III wildland apparatus with its own body design that can hold a spare tire, a different pump capacity, and space "so the vehicle is prepped for everything, and the crew will be able to live out of the apparatus."

A Type III wildland apparatus typically carries 500 gallons of water, a pump with a minimum capacity of 150 gallons per minute (gpm), and 1,000 feet of 1½-inch and 500 feet of one-inch hose. "We've built Type III wildland vehicles with water tanks of up to 600 gallons and Type IV rigs with 750 gallons of water," Trinkner notes. Type IV apparatus have less hose and pump capacity requirements than Type IIIs.

Doug Kelley, wildland product manager for KME, says recent developments in pumps and in remote turrets have improved the performance of wildland vehicles. "The big thing that KME focuses on is pump-and-roll capability, where we have developed pumping systems with dual impellers and single manifolds that allow for low- and high-pressure systems," Kelley says. "We can get 100 gpm at 150 pounds per square inch (psi) at engine idle or, with a four-wheel-drive vehicle, can crawl along in low range and expend water and class A foam on a fire."

KME delivers that pump-and-roll capability chiefly through its Ridgerunner apparatus, designed as a WUI vehicle that can handle both structure and wildland fires. Ridgerunner is available on an International 7400 chassis and carries a Hale 1,500-gpm pump that provides 100 gpm at 150 psi for pump-and-roll situations, an 800-gallon Poly tank, a 20-gallon foam cell, and a FoamPro 2001 direct-injection foam system.

Scott Oyen, vice president of sales for Rosenbauer, says that urban interface pumpers meeting all the criteria as Type I units also can make effective wildland apparatus. "Those that meet the Type I, II, and III classifications might be able to get Insurance Services Organization (ISO) rating points for the fire department," he points out. "That's where our Timberwolf fits in, built on an International 4400 four-door 4x4 chassis with a 500-gpm Darley JSP fire pump, 500 gallons of water, extended front bumper with crosslay, remote bumper turret, high-pressure booster reels in the cab steps, and rescue tool storage.

(1) Pierce Read more 980 0 Article rating: No rating Posted: Jul 8, 2013 Technology - Good and Bad By Chris Mc Loone In late May, a Washington, D.C., ambulance shut down while transporting a gunshot victim. The ambulance operator was able to safely pull the vehicle over to the side of the road to await another unit to finish the transport to the hospital. Immediately prior to the engine failing, the operator noted a light had illuminated that indicated engine failure was imminent. News reports out of Washington, D.C., that week reported it was the emissions control system that caused the problem. I wasn't convinced it was an emissions control problem. Although logically it made sense based on the vehicle's age, it just didn't figure to be the cause-unless regens weren't being performed. Unless there was something really wrong with system, the driver would have been signaled multiple times before the engine actually derated-IF everything was working properly. So I was disappointed that this looked like a case of not performing aftertreatment regeneration when prompted or that the emissions system was being made a scapegoat here. A week after the incident, news arrived that the culprit was actually a faulty fuel cooler screen that caused the engine to shut down. These 2010 engines have caused a good deal of consternation for fire departments all over the country. The Washington, D.C., Fire Department did the right thing and conducted an investigation into the incident and discovered the actual cause of the engine shutdown. However, remember to not let our general displeasure with EPA-compliant engines cause you to rush to judgment when an apparatus or ambulance experiences engine trouble. And, whatever you do, don't delay your regens unnecessarily. Legitimate problems with emissions control systems may occur, but do everything you can to ensure your operations are not the cause of the problems. Technology and the Fire Service The use of new technology within the fire service has come up in a number of my conversations recently. Topics ranged from how to use it, the cost of it, why the fire service embraces it or doesn't embrace it, and so on. There is any number of answers to any of those questions. Any time a product employing a new technology allows us to complete our tasks more safely and efficiently, it's a no-brainer, to me, to put it to use. A case in point is a recent training night at which several line officers and firefighters got a chance to use a new hydraulic tool power unit. We all got a chance to use the new product, inspect it, and learn about it. The technology in this case was using a lithium ion battery as the unit's power source. The instructor began the conversation by stating that there is a great deal of fear out there regarding battery-operated tools. Many departments know firsthand how the NiCad batteries we had charging in our trucks connected to shorelines had dismally short life-spans. Lithium ion batteries, however, are a whole different game. Questions ranged from whether the tool would work slower as the battery strength diminished, what the overall lifetime of the battery is, how long we can work off the battery before the power unit shuts down, how many stages the pump has, and so on. In one hour and seven minutes, we performed three door removals, one B-post removal, and a vertical displacement and removed the trunk lid for good measure. Our instructor also reviewed some new tactics for rescue scenarios. Using a power unit with this technology to me is a no-brainer. It's quiet. There is no exhaust-which is good for the rescuer and the rescued. The truck's generator is not running, so it's not pumping out diesel exhaust into the air around the rescuers. No generator means no cord reels to trip over-health and safety are covered right off the bat. Powering up the unit is with the touch of a button. The rescuer literally picks it up with a tool and hydraulic hose and goes. There is no waiting for the gener Read more 856 0 Article rating: No rating RSS FirstPrevious8456845784588459846084618462846384648465NextLast Theme picker Filter News Catagories Categories News (193) RSS Expand/Collapse Washington News (11847) RSS Expand/Collapse National News (11518) RSS Expand/Collapse WFC News (109) RSS Expand/Collapse Legislative Announcements (7) RSS Expand/Collapse Flag Lowerings (15) RSS Expand/Collapse Memorial Information (24) RSS Expand/Collapse Sections (6) RSS Expand/Collapse Emergency Medical Services (1) RSS Expand/Collapse Fire Administrative Support (17) RSS Expand/Collapse Fire Mechanics (18828) RSS Expand/Collapse Fire Training Safety & Officers (25) RSS Expand/Collapse Public Fire Educators (4) RSS Expand/Collapse HazMat Committee (0) RSS Expand/Collapse Filter to see National, Washington or WFC News, or filter to the Section News you are looking for! Search News Articles Search Terms Of Use | Privacy Statement - Copyright 2024 by Washington Fire Chiefs Home Members About Us News Calendar Resources Documents Sections County Fire Chiefs FRWC WSAFM